Step Plumbing Guide for Installing a Bathtub
Request EstimateWe've encountered this article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround directly below on the net and decided it made perfect sense to talk about it with you in this article.
Setting up a tub isn't exactly rocket science, however it does require strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard job. If the old bathtub is easily easily accessible, the task can move quickly; if you need to open up a wall to eliminate the old bathtub and also position the brand-new bath tub, the job is a lot harder. In either instance, the job is within a residence handyman's skills, although you will certainly need a helper to vacate the old bathtub as well as embeded in the brand-new one. Ensure you have actually certified yourself for the job as well as fit trying it. As opposed to employing a contractor to take over a halfway-completed task, it is much better to think about utilizing one before you start. Chances are you may require an expert plumber to make tube links.
This short article will help you set up a new bath tub in your washroom if you have already purchased a brand-new tub and do not require to alter the plan of your previous water pipes.
Your devices as well as material list should make up the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your setup, then the first thing you must do is detach the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite problematic due to the limited accessibility that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly originate from the pipelines. When the supply pipelines have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from transforming throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing substance.
Before going on to fit the brand-new taps, compare the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end offers a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap and also the sink. Protect the tap in place with the maker given backnut. When the faucet is firmly in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The former type should be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bathtub
Using the two wooden boards under its feet, place the tub in the needed setting. The wood boards are handy in evenly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four little points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the bath tub till the level checks out level.
To set up faucets, fit all-time low of the furthest adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the same for the other faucet.
Switch on the water and check all joints as well as new pipework for leaks and also tighten them if necessary. Fill the tub as well as additionally inspect the overflow outlet as well as the regular electrical outlet for leakages.
Finally, deal with the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the bath tub ought to wait up until the tub has actually been used at least once as this will settle it into its final placement.
Preparing for the Installation
Firstly, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the supplier's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets unit to avoid pressure on the bathtub.
Fit the adaptable faucet ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can move enough to fracture a stiff seal, creating the water to permeate the wall between the bath and the tiling, causing difficulties with moisture and also feasible leaks to the ceiling below.
You can pick from a selection of coloured sealers to blend in your components and also installations. They are marketed in tubes as well as cartridges, and can sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of drenched newspaper or soft rope. Remember to always load the bath tub with water before sealing, to enable the motion experienced when the tub remains in usage. The sealant can break relatively early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently readily available on the marketplace. It is recommended to fit the ceramic tiles making use of waterproof or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that article about Installing A Bathtub from an associate on a different blog. Sharing is caring. You won't know, you will be doing someone a favor. I enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Trusted, top-tier plumbing response.